Email this article The influence of initial radial deformations on the residual stresses distribution in the hardened layer
- Authors: Sazanov V.1, Pavlov V.1, Vakulyuk V.1, Pismarov A.1
-
Affiliations:
- Samara National Research University (Samara University)
- Issue: Vol 5, No 1 (2019): 18.02.2019
- Pages: 14-21
- Section: Articles
- Published: 18.02.2019
- URL: https://dynvibro.ru/dynvibro/article/view/6679
- DOI: https://doi.org/10.18287/2409-4579-2019-5-1-14-21
- ID: 6679
Cite item
Full Text
Abstract
The study of the initial radial deformations influence on the residual strained state components distribution through the hardened layer thickness under various types of surface hardening has been conducted. Chemical thermal machining (CTM) and shot blasting (SB) have been examined on the example of smooth solid steel cylindrical specimens with diameters D=10 mm and D=25 mm under a linear distribution of initial deformations through the hardened layer thickness (the maximum value is on the surface and zero on the maximum depth of hardening). The calculation has been conducted with use of the program complex PATRAN/NASTRAN. The solution has been carried out in axial symmetric positing by thermo elasticity method. On study results it’s been stated that the radial stresses through the hardened layer thickness under CTM and SB are positive. Incidentally the radial component of initial deformations under chemical thermal machining and shot blasting doesn’t exercise essential influence on the radial and axial residual stresses distribution through the hardened layer thickness. Hence the initial radial deformations haven’t much significance at the evaluation of the residual strained stress state influence on the hardened parts endurance limit increment calculated by the average integral residual stresses criterion.
About the authors
Vyacheslav Sazanov
Samara National Research University (Samara University)
Email: sazanow@mail.ru
candidate of technical science, associate professor of strength of materials department
Russian FederationValentin Pavlov
Samara National Research University (Samara University)
Author for correspondence.
Email: pavlov.vf@ssau.ru
doctor of technical sciences, head of strength of materials department
Russian FederationVladimir Vakulyuk
Samara National Research University (Samara University)
Email: vak.v.s@yandex.ru
doctor of technical sciences, professor of strength of materials department
Russian FederationAndrej Pismarov
Samara National Research University (Samara University)
Email: sopromat@ssau.ru
postgraduate student of strength of materials department
Russian FederationReferences
- Pavlov, V.F. (1986), “O svyazi ostatochnyh napryazhenij i predela vynoslivosti pri izgibe v usloviyah koncentracii napryazhenij” , Izvestiya vusov. Маshinostroeniye , no. 8, pp. 29-32.
- Pavlov, V.F. (1988), “Vliyanie na predel vynoslivosti velichiny i raspredeleniya ostatochnyh napryazhenij v poverhnostnom sloe detali s koncentratorom. Soobshchenie I. Sploshnye detail” . Izvestiya vusov. Маshinostroeniye , no. 8, pp. 22-26.
- Pavlov, V.F., Kirpichev, V.A. and Vakulyuk, V.S. (2012), Prognozirovanie soprotivleniya ustalosti poverhnostno uprochnyonnyh detalej po ostatochnym napryazheniyam . Samara: Izdatel'stvo SNC RAN , 125 pp.
- Birger, I.A. (1963), Ostatochnye napryazheniya , Маshgiz, Moscow, Russia, 232 pp.
- Ivanov, S.I. (1971), “K opredeleniyu ostatochnyh napryazhenij v cilindre metodom kolec i polosok. Ostatochnye napryazheniya” . Kuibyshev: KuAI , Issue 53, pp. 32-42.
- Sazanov, V.P., Kirpichev, V. A., Vakulyuk, V.S. and Pavlov, V.F. (2015), “Opredelenie pervonachal'nyh deformacij v uprochnyonnom sloe cilindricheskoj detali metodom konechno-ehlementnogo modelirovaniya s ispol'zovaniem raschyotnogo kompleksa PATRAN/NASTRAN” , Vestnik UGATU , vol. 19, no. 2, Issue 68, pp. 35-40.
- Sazanov, V.P. (2012), “Issledovanie raspredeleniya komponentov ostatochnogo napryazhyonnogo sostoyaniya v oblasti naimen'shego secheniya poverhnostno uprochnyonnoj detali s kol'cevym nadrezom metodom konechno-ehlementnogo modelirovaniya” , Vestnik SGAU , no. 3, Issue 34, pp. 158-161.
- Sazanov, V.P., Chirkov, A.V., Semenova, O.Yu. and Ivanova, A.V. (2012), “Modelirovanie ostatochnogo napryazhyonnogo sostoyaniya detali v usloviyah koncentracii napryazhenij s ispol'zovaniem programmnogo kompleksa PATRAN/ NASTRAN” , Vestnik SamGTU , no. 1, Issue 33, pp. 106-114.
- Pavlov, V.F., Kirpichev, V. A., Vakulyuk, V.S. and Sazanov, V.P. (2014), “Vliyanie poverhnostnogo uprochneniya na predel vynoslivosti cilindricheskih detalej razlichnogo diametra” , Izvestiya vusov , no. 3, pp. 324-326.
- Timoshenko, S.P. and Goodier, G. (1979), Teoriya uprugosti , Science, Moscow, Russia, 341 p.
- Radchenko, V.P., Pavlov, V.F. and Saushkin, M.N. (2015), “Issledovanie vliyaniya anizotropii poverhnostnogo plasticheskogo uprochneniya na raspredelenie ostatochnyh napryazhenij v polyh i sploshnyh cilindricheskikh obrazcakh” , Vestnik Permskogo nacional'nogo issledovatel'skogo universiteta. Mekhanika , no.1, pp. 130-147. doi: 10.15593.perm/mech/2015.1.09
- Saushkin, M.N., Radchenko, V.P. and Pavlov, V.F. (2011), ‘Metod raschyota polej ostatochnyh napryazhenij i plasticheskih deformacij v cilindricheskikh obrazcah s uchyotom anizotropii processa poverhnostnogo uprochneniya” , PMTF , vol. 52, no. 2, pp. 173-182.
- Vindokurov, I.V., Vladykin, A.V., Keller, I.E., Petukhov, D.S., Plyusnin, V.V. and Trofimov, V.N. (2018), “K voprosu o rekonstrukcii ostatochnyh napryazhenij i deformacij plastiny posle drobestrujnoj obrabotki” , Vestnik Samarskogo gosudarstvennogo tekhnicheskogo universiteta. Seriya Fizmat nauki , vol. 22, no. 3, pp. 40-64. doi: 10.14498/vsgtu1602
- Radchenko, V.P. and Saushkin, M.N. (2005), Polzuchest' i relaksaciya ostatochnyh napryazhenij v uprochnyonnyh konstrukciyah , Mechanical Engineering – 1, Moscow, Russia, 226 pp.
Supplementary files
