Email this article THE ESTIMATION OF ROLLER STRENGTHENING INFLUENCE ON THE ENDURANCE LIMIT OF SHAFTS WITH PRESSURIZED HUB
- Authors: Pavlov V.F.1, Vakulyuk V.S.1, Sazanov V.P.1, Efrosinin A.V.1
-
Affiliations:
- Samara University
- Issue: Vol 5, No 4 (2019): 12.12.2019
- Pages: 29-35
- Section: Articles
- Published: 12.12.2019
- URL: https://dynvibro.ru/dynvibro/article/view/7699
- DOI: https://doi.org/10.18287/2409-4579-2019-5-4-29-35
- ID: 7699
Cite item
Full Text
Abstract
The influence of roller strengthening on endurance limit under bending of the 25 mm and 50 mm diameter shafts made of steel 20 and 25 mm diameter shafts made of steel 40X with a pressurized hub has been examined. It’s been stated that the endurance limit of roller strengthened shafts with a pressurized hub depends not only on a value of compressive residual stresses in their dangerous section but on the character of its distribution. The valuation of a surface hardening influence on the endurance limit of shafts by the surface residual stresses criterion and the average integral residual stresses criterion has been shown that the average integral residual stresses criterion calculated through the part’s dangerous section surface layer thickness equal the critical depth of the non-propagating fatigue crack can be recommended for the hardened shafts with a pressurized hub endurance limit increase prediction. It’s been shown that on a diameter of a shaft with a pressurized hub raising it is necessary to increase a thickness of a hardened surface layer with compressive residual stresses.
About the authors
Valentin Fyodorovich Pavlov
Samara University
Author for correspondence.
Email: pavlov.vf@ssau.ru
doctor of technical sciences, head of strength of materials department
Russian FederationVladimir Stepanovich Vakulyuk
Samara University
Email: vak.v.s@yandex.ru
doctor of technical sciences, professor of strength of materials department
Russian FederationVyacheslav Petrovich Sazanov
Samara University
Email: sazanow@mail.ru
candidate of technical science, associate professor of strength of materials department
Russian FederationArsenij Vital'evich Efrosinin
Samara University
Email: sopromat@ssau.ru
postgraduate student of strength of materials department
Russian FederationReferences
- Sveshnikov, D.A., Kudryavtsev, I.V., Gulyaeva, N.A., Golubovskaya, L.D., (1966) Soprotivleniye ustalosti tzementovannych i tzianirovannych stalej primenitel’no k zubchatym kolesam . Voprosy prochnosti i dolgovechnosti mashinostroitel'nyh materialov i detalej. M.: VNIITMASH, ONTI , pp. 48-55. (in Russian).
- Kravchenko, B.A., Mitryaev, K.F., (1968) Obrabotka i vynoslivost’ vysokoprochnych materialov . Kujbyshev: Kujbyshevskoe knizhnoe izdatel'stvo , 131 pp. (in Russian).
- Serensen, S.V., Borisov, S.P., Borodin, N.A., (1969) K voprosu ob otzenke soprotivleniya ustalosti poverhnostno uprochnyonnyh obraztzov s uchetom kinetiki ostatochnoy napryajennosti . Problemy prochnosti , no. 2, pp. 3-7. (in Russian).
- Turovsky, M.L., Shifrin, N.M., (1970) Kontzentratziya napryazhenij v poverhnostnom sloe tzementovannoy stali . Vestnik machinostroyeniya , no. 11, pp. 37-40. (in Russian).
- Ivanov, S.I., Pavlov, V.F., (1976) Vliyanie ostatochnyh napryazhenij na ustalostnuyu prochnost’ . Problemy prochnosti , no. 5, pp. 25-27. (in Russian).
- Ivanov, S.I., Pavlov, V.F., Prokhorov, А.А., (1988) Vliyanie ostatochnyh napryazhenij na soprotivlenie ustalosti pri kruchenii v usloviyah koncentracii napryazhenij . Problemy prochnosti , no. 5, pp. 31-33. (in Russian).
- Pavlov, V.F., (1986) O svyazi ostatochnyh napryazhenij i predela vynoslivosti pri izgibe v usloviyah koncentracii napryazhenij . Izvestiya vusov. Маshinostroeniye , no. 8, pp. 29-32. (in Russian).
- Pavlov, V.F., Kirpichev, V.A., Vakulyuk, V.S., (2012) Prognozirovanie soprotivleniya ustalosti poverhnostno uprochnyonnyh detalej po ostatochnym napryazheniyam . Samara: Izdatel'stvo SNC RAN , 125 pp. (in Russian).
- Ivanov, S.I., (1971) K opredeleniyu ostatochnyh napryazhenij v cilindre metodom kolec i polosok. Ostatochnye napryazheniya . Kuibyshev: KuAI , issue 53, pp. 32-42. (in Russian).
- Radchenko, V.P., Pavlov, V.F., (2011) Naibol’shaya velichina sjimayutschych ostatochnyh napryazhenij pri poverhnostnom uprochnenii detalej . Trudy MNTK «Prochnost' materialov i elementov konstrukcij». Kiev: IPP im.G.S. Pisarenko NANU , pp. 354-357. (in Russian).
- Filatov, E.Ya., Pavlovsky, V.E., (1985) Universal’niy complex mashin dlya ispytaniya materialov i konstruktzij na ustalost’ . Kiev: Naukova Dumka , 92 pp. (in Russian).
- Pavlov, V.F., (1988) Vliyanie na predel vynoslivosti velichiny i raspredeleniya ostatochnyh napryazhenij v poverhnostnom sloe detali s koncentratorom. Soobshchenie I. Sploshnye detali . Izvestiya vusov. Маshinostroeniye , no. 8, pp. 22-26. (in Russian).
- Serensen, S.V., Kogayev, V.P., Shneyderovich, R.M., (1975) Nesutschaya sposobnost’ i raschet detaley mashin na prochnost’ . Moscow: Machinostroyeniye (Mechanical Engineering), 488 pp. (in Russian).
- Kirpichev, V.A., Filatov, A.P., Karanaeva, O.V., Chirkov, A.V., Semenova, O.Yu., (2011) Prognozirovanie predela vynoslivosti poverhnostno uprochnyonnyh detalej pri razlichnoy stepeni contzentratzii napryazhenij . Trudy MNTK «Prochnost' materialov i elementov konstrukcij». Kiev: IPP im. G.S. Pisarenko NANU , pp. 678–685. (in Russian).
Supplementary files
