THE INFLUENCE OF HYDRO BLASTING ON THE EN-DURANCE LIMIT OF SPECIMENS WITH A CUT UNDER BENDING AND STRETCHING-COMPRESSION

Cover Page

Cite item

Full Text

Abstract

The hydro blasting influence on an endurance limit of cylindrical specimens with circular cuts of a semicircular  profile of 0,3 mm radius under bending and stretching-compression in a case of symmetric cycle has been examined. Specimens of 10 mm diameter for fatigue tests were made of steels 30ХГСА, 12Х18Н10Т, ЭИ961,45 and aluminum alloys В93, Д16Т.The influence of surface hardening on an endurance limit of specimens with cuts was valuated by two criteria: residual stresses on the concentrator surface and the average integral residual stresses calculated through the part’s dangerous section surface layer thickness equal the critical depth of a non-propagating fatigue crack.

On results of residual stresses and specimens with cuts endurance limits determination it’s been stated that coefficients of surface hardening influence on an endurance limit increase under bending and stretching-compression by two criteria are approximately equal. Besides, the coefficient of the influence by the average integral residual stresses criterion changes within essentially lesser limits than the coefficient of the influence by the residual stresses on the concentrator surface criterion. So the average integral residual stresses criterion should be used for the evaluation of a surface hardening influence on an endurance limit of parts with concentrators.

On an example of specimens within and without peening in a dangerous section it’s been shown that peening doesn’t influence the endurance limit of a surface hardened part. The compressive residual stresses only influence the endurance limit of these parts.

About the authors

Valentin Fyodorovich Pavlov

Samara University

Author for correspondence.
Email: pavlov.vf@ssau.ru

doctor of technical sciences, head of strength of materials department of Samara National Research University (Samara University)

Russian Federation

Viktor Alekseevich Kirpichyov

Samara University

Email: kirpichev.va@ssau.ru

doctor of technical sciences, professor of strength of materials department of Samara National Research University (Samara University)

Russian Federation

Vladimir Stepanovich Vakulyuk

Samara University

Email: vak.v.s@yandex.ru

doctor of technical sciences, professor of strength of materials department of Samara National Research University (Samara University)

Russian Federation

Vyacheslav Petrovich Sazanov

Samara University

Email: sazanow@mail.ru

candidate of technical science, associate professor of strength of materials department of Samara National Research University (Samara University)

Russian Federation

Pavel Anatol'evich Shlyapnikov

Samara University

Email: sopromat@ssau.ru

postgraduate student of strength of materials department of Samara National Research University (Samara University)

Russian Federation

References

  1. Ivanov, S.I., Pavlov, V.F., (1974) О vliyanii ostatochnyh napryazhenij i naklepa na ustalostnuyu prochnost' obraztzov iz stali 45 . Voprosy prochnosti elementov aviacionnyh konstrukcij. Kujbyshev: KuAI , issue 1, pp. 96-100. (in Russian).
  2. Ivanov, S.I., Pavlov, V.F., (1976) Vliyanie ostatochnyh napryazhenij na ustalostnuyu prochnost’ . Problemy prochnosti , no. 5, pp. 25-27. (in Russian).
  3. Ivanov, S.I., Pavlov, V.F., Prokhorov, А.А., (1988) Vliyanie ostatochnyh napryazhenij na soprotivlenie ustalosti pri kruchenii v usloviyah koncentracii napryazhenij . Problemy prochnosti , no. 5, pp. 31-33. (in Russian).
  4. Vakulyuk, V.S., (2012) Soprotivlenie ustalosti detali v zavisimosti ot tolshchiny uprochnyonnogo sloya pri ope-rezhayushchem poverhnostnom plasticheskom deformirovanii . Vestnik SGAU , no.3 (34), part 1, pp. 172-176. (in Russian).
  5. Kirpichyov, V.A., Bukaty, A.S., Chirkov, A.V., (2012) Prognozirovanie soprotivleniya ustalosti poverhnostno up-rochnyonnyh gladkih detalej . Izvestiya vuzov. Povolzhskij region. Tekhnicheskie nauki , no.3 (23), pp. 102-107. (in Russian).
  6. Pavlov, V.F., (1986) O svyazi ostatochnyh napryazhenij i predela vynoslivosti pri izgibe v usloviyah koncentracii napryazhenij . Izvestiya vusov. Маshinostroeniye , no. 8, pp. 29-32. (in Russian).
  7. Pavlov, V.F., (1988) Vliyanie na predel vynoslivosti velichiny i raspredeleniya ostatochnyh napryazhenij v pover-hnostnom sloe detali s koncentratorom. Soobshchenie I. Sploshnye detali . Izvestiya vusov. Маshi-nostroeniye , no. 8, pp. 22-26. (in Russian).
  8. Pavlov, V.F., (1988) Vliyanie na predel vynoslivosti velichiny i raspredeleniya ostatochnyh napryazhenij v pover-hnostnom sloe detali s koncentratorom. Soobshchenie II. Polye detali . Izvestiya vusov. Маshi-nostroeniye , no. 12, pp. 37-40. (in Russian).
  9. Pavlov, V.F., Kirpichev, V.A., Vakulyuk, V.S., (2012) Prognozirovanie soprotivleniya ustalosti poverhnostno up-rochnyonnyh detalej po ostatochnym napryazheniyam . Samara: Izdatel'stvo SNC RAN , 125 pp. (in Russian).
  10. Ivanov, S.I., Pavlov, V.F., Minin, B.V., Kirpichev, V.A., Kocherov, E.P., Golovkin, V.V., (2015) Ostatochnye napryazheniya i soprotivlenie ustalosti vysokoprochnykh rez'bovykh detaley . Samara: Izdatel'stvo SNC RAN , 170 pp. (in Russian).
  11. Birger, I.A., (1963) Ostatochnye napryazheniya . М.: Маshgiz , 232 pp. (in Russian).
  12. Ivanov, S.I., (1971) K opredeleniyu ostatochnyh napryazhenij v cilindre metodom kolec i polosok. Ostatochnye napryazheniya . Kuiby-shev: KuAI , issue 53, pp. 32-42. (in Russian).
  13. Ivanov, S.I., Grigoryeva, I.V., (1971) K opredeleniyu ostatochnyh napryazhenij v cilindre metodom snyatiya chasti poverkhnosti . Voprosy prochnosti elementov aviacionnyh konstrukcij. Kujbyshev: KuAI , issue 48, pp.179-183. (in Russian).
  14. Ivanov, S.I., Shatunov, M.P., Pavlov, V.F., (1974) Vliyanie ostatochnyh napryazhenij na vynoslivost' obrazcov s nadrezom . Voprosy prochnosti elementov avi-acionnyh konstrukcij. Kujbyshev: KuAI , issue 3, pp. 88-95. (in Russian).
  15. Ivanov, S.I., Shatunov, M.P., Pavlov, V.F., (1973) Opredeleniye dopolnitel’nyh ostatochnyh napryazhenij v nadrezah na cilindricheskih detalyah . Voprosy prochnosti elementov aviacionnyh konstrukcij. Kujbyshev: KuAI , issue 66, pp. 160-170. (in Russian).
  16. Sazanov, V.P., Chirkov, A.V., Samoylov, V.A., Larionova, Yu.S., (2011) Modelirovanie pereraspredeleniya ostat-ochnyh napryazhenij v uprochnyonnyh cilindricheskih obrazcah pri operezhayushchem poverhnostnom plasticheskom deformirovanii . Vestnik SGAU no. 3 (27), part 3, pp. 171-174. (in Russian).
  17. Sazanov, V.P., (2012) Issledovanie raspredeleniya komponentov ostatochnogo napryazhyonnogo sostoyaniya v oblasti naimen'shego secheniya poverhnostno uprochnyonnoj detali s kol'cevym nadrezom metodom konechno-ehlementnogo modelirovaniya . Vestnik SGAU , no. 3 (34), pp. 158-161. (in Russian).
  18. Sazanov, V.P., Chirkov, A.V., Semenova, O.Yu., Ivanova, A.V., (2012) Modelirovanie ostatochnogo napryazhy-onnogo sostoyaniya detali v usloviyah koncentracii napryazhenij s ispol'zovaniem programmnogo kompleksa PATRAN/ NASTRAN . Vestnik SamGTU , no. 1 (33), pp. 106-114. (in Russian).
  19. Sazanov, V.P., Kirpichev, V. A., Vakulyuk, V.S., Pavlov, V.F., (2015) Opredelenie pervonachal'nyh deformacij v uprochnyonnom sloe cilindricheskoj detali metodom konechno-ehlementnogo modelirovaniya s ispol'zovaniem raschy-otnogo kompleksa PATRAN/NASTRAN . Vestnik UGATU , vol. 19, no. 2 (68), pp. 35-40. (in Russian).
  20. Pavlov, V.F., Sazanov, V.P., Vakulyuk, V.S., (2019) K voprosu otzenki vliyaniya hidrodrobestruynoy obrabotki na predel vynoslivosti detaley po pervonachal’nym deformatziyam obraztza-svidetelya . Vestnik PNIPU. Mashinostroenie, materi-alovedenie , no.1, vol. 21, pp. 55-62. (in Russian).
  21. Radchenko, V.P., Pavlov, V.F., (2010) Naibol’shaya velichina sjimayutschikh ostatochnyh napryazhenij i mek-hanicheskie kharakteristiki materiala poverkhnostno uprochnyonnoj detali . Matematicheskoe modelirovanie i kraevye zadachi. Trudy sed'moj Vserossijskoj nauchnoj konferencii s mezhdunarodnym uchastiem. Samara: SamGTU , part. 1, pp. 249-252. (in Russian).
  22. Radchenko, V.P., Pavlov, V.F., (2011) Naibol’shaya velichina sjimayutschych ostatochnyh napryazhenij pri poverhnostnom uprochnenii detalej . Trudy MNTK «Prochnost' materialov i elementov konstrukcij». Kiev: IPP im.G.S. Pisarenko NANU , pp. 354-357. (in Russian).
  23. Serensen, S.V., Kogayev, V.P., Shneyderovich, R.M., (1975) Nesutschaya sposobnost’ i raschet detaley mashin na prochnost’ . Moscow: Machinostroyeniye (Mechanical Engi-neering), 488 pp. (in Russian).

Supplementary files

Supplementary Files
Action
1. JATS XML
Download

Copyright (c) 2020 Валентин Фёдорович Павлов, Виктор Алексеевич Кирпичёв, Владимир Степанович Вакулюк, Вячеслав Петрович Сазанов, Павел Анатольевич Шляпников

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Journal of Dynamics and Vibroacoustics

ISSN 2409-4579 (Online)

Publisher and Founder: Samara National Research University, 34, Moskovskoye shosse, Samara, 443086, Russian Federation.

Extract from the register of registered media

Editor-in-chief:  Academician of the RAS
E. V. Shakhmatov 

4 issues per year.

Free price

Editorial address: room 324, 43, Gaya street, Samara, 443086

Address for correspondence: 34, Moskovskoye shosse, Samara, 443086, Russian Federation, Samara National Research University (room 324, building 14)

Phone: 8 (846) 267 47 66

e-mail: dynvibro@ssau.ru

www: https://dynvibro.ru

© Samara University

 

This website uses cookies

You consent to our cookies if you continue to use our website.

About Cookies